DISCLAIMER: I have no association with UVB-76 station, neither do I have any clue what is the content I am relaying. I can only assure, that the signal is received on 4.625MHz AM-modulated 900km NW from supposed origin and retransmitted unaltered. In no way can I guarantee this service, nor be considered responsible of any content re-transmitted. The only purpose for this relay to exist is because lot of people who do not have equipment or are located too far from station seem to be interested about listening to it. Should the UVB-76 station- or transmission content owners feel violated in any way, please contact me at uvb76.repeater@gmail.com and we will work it out.

Note, that because of shortwave radio signal propagation specifics the station can be more or less reliably received from around 4pm to 6am GMT on summertime. It is almost 24h audible during the winter, with short "skip-zone" blank-out around 6pm GMT.

The USB feed is considered as main source of audio today, as the voice messages are much better audible there than on the AM stream. However, the buzzer sound from the AM stream is somewhat more pleasant to listen at, so both feeds are kept simultaneously.

Sunday, November 27, 2011

Jazzsequence - The Signal, a Pledge

UVB-76 has been a great deal of inspiration for musicians around the world, resulting many beautiful tracks. If you think there is room for more, please check the link what was just sent to me today by a good old friend Margus, who' s one of the greatest analog synth fans I know and runs a after-life site for old Roland synths (http://www.wolzow.com/)

Its a pledge by Chris Reynolds (a.k.a. Jazzsequence) for rising $900 for releasing an album inspired from listening to the shortwave and UVB-76 in particular. As far as I understood, the money is going to be spent on couple of cool gizmos helping to make a music in a specific way, but its a reasonable cause nevertheless as far as I can tell :)

Tuesday, November 15, 2011

SDR MK1.5 'Andrus' Software Radio Design Finished!

Its done! I have finally finished the SDR MK1.5 design! For those not familiar with what I am talking, here is a little intro.

The Software Defined Radio, or SDR, sometimes also referred as Software Radio, is a new generation of radio receivers what allow the reception of the radio signals with your computer software. The Software Radio is acting like an interface between the antenna and your computer. I have created a more technical overview about Software Radio architectures on SDR MK1 page, but the basic idea is, that the SDR Receiver is receiving the high frequency signal from antenna, makes it a digital signal and does some pre-processing, like frequency downconversion and digital filtering. The processed signal is then fed to the computer (on our case through USB or Network interface) and then visualized, decoded etc. on the computer software. 

The long-over-the-schedule radio boards went finally into production last night. It has taken four months longer than originally expected for a very good reason: The first fifteen MK1 units on the field got very warm feedback, but even more suggestions of what and how could be done differently. Therefore getting the design updated was a endless struggle between adding things and making a decision what shall be left out for a reason or another.

Here is a short recap on a design logic the new radio follows.

There are three main areas the radio has evolved from the MK1 design:

- First, it is now just a radio of better quality. The long list of small technical changes (many of which can probably be appreciated only by RF professionals and radio amateurs) will altogether account to a better noise floor and more precise signal reconstruction. While this is not important for an analog transmissions that much, the people working on a shortwave digital domain, DX-ing and signal hunting will
hopefully appreciate it.

- Second, the radio is now having a network interface besides USB and a 32-bit 60MHz clock CPU from Atmel. Both additions will drastically enhance the received signal bandwidth and connectivity: We are now capable to process up to 820kHz bandwidth on single channel through network and get the much desired 192kHz through the audio interface. The added mobility what network interface together with PoE (Power Over Ethernet) extension possibility will give, can allow this radio to be called a "network antenna" adapter!

- Third major change in design logic is that the radio extension capabilities are much re-visited and the MK1.5 can now be treated as a motherboard for a future experimentation, would it be an extension boards by myself or your own creation. This includes the jumpers on few selected places what allow adding the new RF boards to the chain, would it be filters on downconverters, and the I2C, SPI, UART and GPIO connectivity. The radio, although being a diversity shortwave receiver right out of box, is also now also a great general ADC platform for future expansion.

One of the first extension boards the SDR MK1.5 will get to utilize this capacity is the Elonics E4000 based downconverter, what will extend the receiver frequency range up to 1.7GHz!

Here is an updated specifications for the SDR MK1.5

  • Dual Channel diversity mode shortwave receiver 
  • Receiving Frequency range 500Hz .. 31MHz both channels
  • USB Audio Interface, 24bit 192kHz
  • 10/100 EThernet interface, with PoE extension possibility
  • IF bandwidth through USB audio 192kHz
  • IF bandwidth through Ethernet 820kHz

Aah, and one more thing - I got a suggestion, that the radio is supposed to have a name. Oddly enough, one of the prospects suggested was my own, so here we go - The SDR MK1.5 is hereby named 'Andrus' :)